客戶在冷再生機出租使用過程中，不可避免地會出現消耗和磨損，其中，冷再生機輸送帶特別容易出現問題，運行時間長，可能出現打滑現象，影響工作效率。讓冷再生機出租廠家帶我們一起來分析下打滑的原因和解決辦法。

In the process of renting and using the cold regenerator, the customer will inevitably encounter consumption and wear. Among them, the conveyor belt of the cold regenerator is particularly prone to problems, running for a long time, and may slip, affecting the working efficiency. Let the cold regeneration machine rental manufacturer take us to analyze the causes and solutions of slipping.

1、初始張力太小。

1. The initial tension is too small.

輸送帶離開滾筒的張力不夠，會引起皮帶打滑。一般來說，這種情況是在啟動時發生的。如果你想解決它，你要調整張力裝置和增加初始張力。

The tension of the conveyor belt leaving the drum is not enough, which will cause the belt to slip. Generally, this happens at startup. If you want to solve it, you need to adjust the tension device and increase the initial tension.

2、摩擦力是不夠的。

2. Friction is not enough.

傳動滾筒與輸送帶之間的摩擦力不足以引起滑動。造成這種現象的主要原因是輸送帶上的水或環境潮濕。解決方法：在氣缸中加入一些松香末。注意不要用手而應用鼓風設備吹入，以免發生事故。

The friction between the drive drum and the conveyor belt is not enough to cause sliding. The main reason for this is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder into the cylinder. Be careful not to blow in by hand with air blower to avoid accidents.

 

 

3、軸承損壞

3. Bearing damage

尾部滾子軸承損壞或不旋轉。造成損壞的原因是機器尾部太浮、太沉，不能及時修理和更換損壞的或不靈活的部件，這導致由打滑引起的阻力增加。

The rear roller bearing is damaged or does not rotate. The cause of damage is that the tail of the machine is too floating and heavy to repair and replace damaged or inflexible parts in time, which leads to increased resistance caused by slipping.

4、起步太快。

4. Start too fast.

起動速度太快，不能打滑。這個時候可慢速啟動。如果使用鼠籠電機，則可以移動兩次，然后被，還可以有效地克服打滑現象。

The starting speed is too fast to slip. It can be started slowly at this time. If a squirrel cage motor is used, it can be moved twice and then activated, and can also effectively overcome the slip phenomenon.

5、輸送帶負荷過大。

5. The conveyor belt is overloaded.

輸送帶的負荷過大，超過電機能力也會打滑。打滑的優點是保護電機。否則，電動機將長期燃燒。但對于運行來說則是打滑事故。

If the load of the conveyor belt is too large, it will slip when exceeding the motor capacity. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is skid accident.

以上是關于冷再生機出租時打滑的原因及方法的介紹，希望對大家有所幫助，感謝您的閱讀，如想了解更多內容歡迎點擊我們的http://lvuee.com官網。

The above is an introduction to the reasons and methods for the slipping of the cold regeneration machine when renting. I hope it will be helpful to you. Thank you for your reading. If you want to know more, please click our http://lvuee.com Official website.